Current Position:HOMEApp BankbookInitial Setup of the App Bankbook

日本語

English

簡体字

Tagalog

Português

Español

ภาษาไทย

Tiếng Việt

Bahasa Indonesia

Initial Setup of the App Bankbook

  • Click here if you are already using the Direct Banking Service
    (For customers that have a logon ID)

  • Click here if you have never used the Direct Banking Service
    (For customers that do not have a logon ID)

Customers that already using the Direct Banking Service
(For customers that have a logon ID)
Detail

Set app logon information

step01Start the app and agree to the Terms of Use.

↓

step02Tap I use the Direct Banking Service > Set Logon Information

↓

step03Enter your Direct Banking logon information

  • Enter the logon ID and password that you are currently using for the Direct Banking Service.

  • Before saving the settings, check that your logon information is correct.

  • If the logon test was successful, tap Save Logon Information.

↓

  • (*3)The following screen will appear only for customers that have registered with the Seven Bank Point Service. Enter your nanaco information registered with the Seven Bank Point Service. (You can also enter this information at a later date)

  • If you want to enter your nanaco logon information now, tap this button

  • If you want to enter your nanaco logon information later, tap this button

↓

step04Set an app passcode.
Enter any four digits and then re-enter the same four digits. Initial setup is now complete.

Customers that have never used the Direct Banking Service
(For customers that do not have a logon ID)
Detail

First, register for the Direct Banking Service.

step01Enter your Seven Bank Account information

  • Enter the following numbers on your cash card after the number 0034:

    • Branch number (three digits)
    • Account number (seven digits)

  • Enter your 7-digit Customer ID written on the back of your cash card or your Direct Banking card.

  • Enter the telephone number that you registered with Seven Bank.

    Make sure that you enter the numbers in the applicable fields.

  • Enter the characters displayed above.

  • Once you have entered all the applicable information, tap Logon ID.

↓

step02Register your logon ID

Make sure that you do not forget the logon ID and password that you set on this screen.

  • Enter the logon ID that you registered.

    • Enter between 6 and 32 single-byte alphanumeric characters.
      (You cannot set a numbers-only logon ID)
  • Tap this button to check that it is a logon ID that you can use.

    • You cannot set a logon ID that another customer is using.

  • Enter the logon password that you registered.

    Enter between 6 and 32 single-byte alphanumeric characters. (You cannot set a letters-only or a numbers-only password.)
    You cannot set your date of birth, registered telephone number, or any other password that can be easily guessed by another person as your password.

  • Enter the PIN that you set for this cash card.

    If the temporary PIN is still unchanged, a screen to set the PIN will appear separately.

  • Check the confirmation number written on the back of your cash card or your Direct Banking card and enter the numbers corresponding to the two red squares.

↓

step03Once you have registered your email address, the Direct Banking Service registration is complete. (If you have already registered your email address, this screen does not appear.)

  • Enter an email address to receive an email confirming your registration.

    If you have email filters configured, set your filters to allow email form the @sevenbank.co.jp domain.

  • After you enter your email address, tap the send button.
    You will receive a confirmation email at the email address you entered.

↓

  • (*3)The following screen will appear only for customers that have registered with the Seven Bank Point Service. Enter your nanaco information registered with the Seven Bank Point Service. (You can also enter this information at a later date)

  • If you want to enter your nanaco logon information now, tap this button

  • If you want to enter your nanaco logon information later, tap this button

↓

step04Proceed to the app passcode setup screen.

↓

step05Set an app passcode.
Enter any four digits and then re-enter the same four digits. Initial setup is now complete.

Go to Top of Page